Clos'O sensor
Presentation
The Clos’O sensor is a LoRaWAN class A sensor that uses a disposable 3.6V A-type battery as power supply and includes an internal antenna.
Clos’O is designed to detect closure or opening of a door or a gate. Time to take account is configurable.
Clos’O records all events (opening, closure).
Main case is fixed on the door frame. A magnet case fixed on the door leaf.
Battery level supervision by alarm sending.
Clos’O is able to detect tamper removal. Alarm is immediately sent.
Accessories to fix main case and magnetic case are supplied.
Integrated sensor in main case with external magnet case.
Family code:
The family code of Clos’O devices is: 50-70-108-xxx
LoraWAN release
v1.0.2 Region Parameter rev B
Casing
Flammability rating: UL94V0
Ingress protection: IP65
Installation and operation
Installation
In construction...
Radio propagation
In order for the sensor to operate correctly, the number of obstacles should be limited in order to avoid excessive radio wave attenuation.
Autonomy
The information in the table below represents how long the battery can last. It is based on the default configuration at ambient temperature (+25°C) within the optimal operating range of the sensor via a LoRaWAN network (one uplink frame), when the spreading factor used is SF12.
The disposable battery has a 3.6Ah capacity, of which 85% is used.
| Transmission periodicity | Battery life |
|---|---|
| 10 frames each day (default configuration with 2 alarms) | 7 years |
Human Machine Interface
The Clos’O sensor has a buzzer that allows it to “communicate” with the user.
A reed switch is available under the sticker. It is possible to use a magnet to activate it and makes specific actions on the sensor (Switch off, switch on, Re-associtation…). When the reed switch is activated, the buzzer rings quickly.
To Start-up the device, it is necessary to put a magnet on the side of the sensor during one second (at the left side of the cable gland). The buzzer rings quickly during this step. After this second, the buzzer stops and rings slowly until the association is done.
To switch off the device, use the same way by putting the magnet during 5 seconds. After this amount of time, the device rings 5 times slowly.
The table below describes the actions to be performed on the reed switch to disable or enable the storage mode.
| Switch ON (disable storage mode) | 1 second | Lecteur audio |
| Switch OFF (enable storage mode) | 5 seconds | Lecteur audio |
When the sensor is trying to associate with a network, it emits the following sound:
Lecteur audioOnce the association is completed, the buzzer makes the following sound:
Lecteur audioA reed switch (or magnetic switch) is available. A magnet can be used to activate it and perform specific actions on the sensor (switch off, switch on, reassociation…).
- Configuration: "void" frames are sent every minute for 10 minutes.
Standard reports are disabled in this mode.
| Way to trigger it | One passage of the magnet near the reed switch or specific ZCL command |
| Way to stop it | Another passage of the magnet or specific ZCL command |
| Effects on the sensor | Lecteur audio |
| Duration | The configuration mode lasts 10 minutes |
- A reassociation procedure can be requested if no downlink frame is received by the sensor during a given periodicity (4 days by default) or if a given number (100 by default) is reached or in case of failure (no acknowledgement received) by sending an applicative frame to the sensor or via the sensor’s IHM.
The sensor keeps the AppEUi and DevAddr configured, Confirmed/Unconfirmed configuration and all applicative configurations. However, LoRaWAN configurations (channel, data rate…) are lost
| Way to trigger it | Three passages of the magnet near the reed switch or ZCL command from LoRaWAN cluster. |
| Effects on the sensor | Lecteur audio |
- A factory reset is available on Watteco’s sensors. It deletes all the applicative settings saved in the flash memory (i.e. configured batches and reports will be deleted).
The sensor keeps the AppEUi and DevAddr configured. However, LoRaWAN configurations (channel, data rate…) and applicative configurations are lost.
| Way to trigger it | Two quick passages and a very long passage (until the sensor rings for the reset) of the magnet near the reed switch |
| Effects on the sensor | Lecteur audio |
Applicative layer
Codecs are available to decode frames: Downloads
The Clos'O device implements “Binary Input” cluster associated to its Inputs.
Clos'O integrates the following clusters:
| Cluster | End Point | Cluster name | Managed attributes |
|---|---|---|---|
| 0x0000 | EP0 | Basic | All |
| 0x0050 | EP0 | Configuration | All |
| 0x8004 | EP0 | LoRaWAN | All |
| 0x000F | EP0: tear off feature | Binary Input | All |
| 0x000F | EP1: open/close feature | Binary Input | All |
Default configuration
The detection of an opening or closing is subject to maintaining the state for a period of filtering.
An alarm of opening or closing is sent after maintening 2 seconds in the state, this state is sent too all 4 hours in a standard frame.
The recording in the batch is done when the opening or closing is maintained during 5 seconds.
The case tear off alarm is sent immediately.
The device send each day its voltage battery in a standard frame.
The batch is configured with the following parameters:
| Label (size = 2) | resolution | |
| Binary Input (opening/closing) | 0 | 1 |
Every change made to the default configuration must comply with the legal duty cycle (for example, the most restrictive in the EU is 0.1%, which corresponds to approximately 1 frame per hour with SF12)
Frame examples
All frames have to be sent on port 125
Standard report
Report
Report of case tear off
Report of closing/opening
Batch of closing/opening
Configuration
Modify the batch
Modify open/close alarm
Remove open/close alarm
