CLIM'O

Presentation

---

The CLIM'O sensor is a LoRaWAN class A sensor that uses a disposable 3.6V AA-type battery as power supply. It also includes an internal antenna.

It measures the temperature, the relative humidity. It is possible to get the voltage of the power supply.

	Accuracy tolerance
Temperature (°C)	+/- 0.2
Humidity (%)	+/- 2

Family code

The family code of CLIM'O devices is: 50-70-247

LoRaWAN release

v1.0.2 Region Parameter rev B

Installation and operation

---

Installation

The housing is intended to be installed inside a building.

First, remove the tab from the battery to start the sensor.

Fix the lid of the sensor to the wall using screws or double-side tape. Then attach the case that contains the electronic board to the lid.

Radio propagation

In order for the sensor to operate correctly, the number of obstacles should be limited in order to avoid excessive radio wave attenuation. It is also important to place the sensor as high as possible, not in contact with outside. The device should be placed away from windows, heat input (sun, radiator, ventilation, air intake,...)

Autonomy

---

The information in the table below represents how long the battery can last. It is based on the default configuration at ambient temperature (+25°C) within the optimal operating range of the sensor via a LoRaWAN network (one uplink frame), when the spreading factor used is SF12.

The disposable battery has a 2.6Ah capacity, of which 85% is used.

Transmission and Measure periodicity	Spreading Factor	Battery life
12 hours / 1 hour	12	10 years
2 hours / 30 min	12	10 years
1 hour / 10 min	12	7 years
1 hour / 10 min	9	10

Human Machine Interface

---

Video Tutorials - WATTECO

There are two LEDs on the device:

Green:      blinking until the association with a network is done. After 6 hours in association searching the led blinks all 1 minute.

Red:     blinking in configuration mode.

A magnet can be used to activate it and perform specific actions on the sensor (switch off, switch on, reassociation…). When the reed switch is activated, the red LED blinks quickly.

To start up the device, a magnet must be placed next to the sensor for one second to the configuration sticker (the "gears"). The red LED blinks quickly during this step. After one second, the red LED stops blinking and the green LED blinks slowly until the association is done.

To switch off the device, repeat the same operation by placing the magnet next to the sensor for 5 seconds. After those 5 seconds, the red LED blinks 5 times slowly.

• Configuration

Configuration mode
Way to trigger it	One passage of the magnet near the reed switch or specific ZCL command
Way to stop it	Another passage of the magnet or specific ZCL command
Effects on the sensor	The CONF led (red) blinks (3 sec. OFF, 3 sec. ON) and the sensor sends an uplink frame every minute.
Duration	The configuration mode lasts 10 minutes

• A reassociation procedure can be requested if no downlink frame is received by the sensor during a given periodicity (4 days by default) or if a given number (100 by default) is reached or in case of failure (no acknowledgement received) by sending an applicative frame to the sensor or via the sensor’s IHM.

The sensor keeps the AppEUI and DevEUI configured, Confirmed/Unconfirmed configuration and all applicative configurations. However, LoRaWAN configurations (channel, data rate …) are lost.

ReAssociation Mode
Way to trigger it	Three passages of the magnet near the reed switch or ZCL command from LoRaWAN cluster.
Effects on the sensor	The ASSN led (green) blinks as the “no commissioned sensor” LED is lit.

• A factory reset is available on Watteco’s sensors. It deletes all the applicative settings saved in the flash memory (i.e. configured batches and reports will be deleted).

The sensor keeps the AppEUi and DevAddr configured. However, LoRaWAN configurations (channel, data rate…) and applicative configurations are lost.

Factory reset
Way to trigger it	Two quick passages and a long passage of the magnet near the reed switch
Effects on the sensor	The CONF LED (red) and ASSN LED (green) blink at the same time briefly. All the applicative settings (for batches and reports) are deleted. The blinking is illustrated below this table.

Applicative layer

---

Codecs are available to decode frames: Downloads

The CLIM'O device integrates the following clusters:

Cluster	Cluster name	Managed attributes
0x0000	Basic	All
0x0050	Configuration	All Threshold is available
0x8004	LoRaWAN	All
0x0402	Temperature Measurement	All Threshold is available
0x0405	Relative Humidity Measurements	All Threshold is available

Default configuration

---

A default configuration is set:

• The device reports a "batch" of temperature / humidity from every 1 hour with a measure all 10 minutes.

The configuration of batch is :

Features	Label (size= 2)	Measure periodicity	Transmission periodicity	resolution
Temperature	0	10 minutes	1 hour	0.1°C
Relative Humidity	1	10 minutes	1 hour	1%
Battery Voltage	2	7 days	7 days	1mV

Every change made to the default configuration must comply with the legal duty cycle (for example, the most restrictive in the EU is 0.1%, which corresponds to approximately 1 frame per hour with SF12)

To decode the default "batch" is necessary to use this argument: 2 0,10,7 1,100,6 2,1,6.

Measurement periodicity

The measurement periodicity depends on the minimum and maximum, and the delta fields.

If the value of the minimum and the delta is 0, then the maximum value is the periodicity of measurement.

However, if the value of delta is different than 0, then the periodicity of measurement is the configured delay of the min field.

In batch mode, if delta = 0 then the measurement is done and recorded all mininmum field delay.

Frame examples

---

All frames have to be sent on port 125

Report

Report of a batch

 

Configuration

Modify report on the temperature